2020 Caterpillar 150-15 Motor Grader For Sale, 4,624 Hours | Big Lake, MN | EQ0169955

Year

2020

Rating	As-Is

Inspection Report

GENERAL COMMENTS	Normal

AIR CONDITION SYSTEM	Okay/Done
AUTO SHIFT	Okay/Done
BRAKE OPERATIONAL	Yes (Passed)
CAB FILTER	Okay/Done
CLEAN CAB	Yes
CLEAN WINDOWS & INSPECT	Okay/Done
CONTROLS	Okay/Done
EMS/CMS/GAUGES	Okay/Done
FUEL LEVEL	Full
HEATING SYSTEM	Okay/Done
OPERATIONAL MANUAL	Yes (Passed)
PARKING BRAKE OPERATIONAL/ ADJUSTED	Okay/Done
PRODUCT LINK BOX	Yes (Passed)
RIDE CONTROL	Okay/Done
SEAT ADJUSTMENT	Yes (Passed)
SEAT CUSHION	Yes (Passed)
TRANS CONTROL	Okay/Done
WASHER FLUID & WIPER CONDITION	Okay/Done

ACCUM CHARGE	Yes (Passed)
AIR FILTER	Yes (Passed)
ALL DOOR LATCHES	Yes (Passed)
BATTERIES	Yes (Passed)
BELLY PANS	Okay/Done
BLOCK HEATER	Yes (Passed)
BOOM	N/A
BRAKE FLUID	Okay/Done
CARRIAGE	N/A
CLEAN MACHINE	Yes
COOLANT LEVEL	Within Operating Range
DAMAGE LISTED	Okay/Done
DEF LEVEL	Full
DRAIN AIR TANKS	N/A
EDGES/TEETH	Okay/Done
ENGINE OIL	Within Operating Range
FAN BELT	Yes (Passed)
FINAL DRIVE	Yes (Passed)
FRONT AXEL	Yes (Passed)
GREASE MACHINE	Yes (Passed)
HAMMER EQUIPPED MACHINES	N/A
HYD CHARGE	Yes (Passed)
HYDRAULIC OIL	Correct
HYDRAULIC PRESSURE	Yes (Passed)
IS THERE ANY HYDRAULIC/CYLINDER LEAKS? IF SO, WHERE IS THE LEAK?	No
KICKOUTS	N/A
LAST PM SERVICE	Yes
LIST ANY PSP/PIPS NEEDED ON MACHINE	Yes
PIVOT SHAFT	N/A
REAR AXEL	Yes (Passed)
SWING DRIVE	N/A
TIRES (LIST ANY DAMAGE, SIZE, & BRAND)	Good
TRACK ADJUSTMENT	N/A
TRACK ROLLER FRAME	N/A
TRANSMISSION OIL	Within Operating Range

BACK UP ALARM	Okay/Done
BRAKE LIGHTS	Okay/Done
GRAB HANDLES	Okay/Done
HEAD LIGHTS	Okay/Done
HORN	Okay/Done
SAFETY LINK	Okay/Done
SEAT BELT (MUST BE REPLACED EVERY 3 YEARS)	Okay/Done
SMV SIGN	Okay/Done
STROBE LIGHTS	N/A
TURN LIGHTS	Okay/Done
ZIEGLER/ZIEGLER RENTAL DECALS AND ID#	Okay/Done

3D TECHNOLOGY GRADE CONTROL EQUIPPED: AFTERMARKET OR CAT GRADE. PROCEED TO NEXT STEPS IF EQUIPMENT IS PRESENT. (SECONDARY DISPLAY IN THE MACHINE)	N/A
FOR EXCAVATORS: IS THE MACHINE ACCURATE IN 2D AGAINST A LP51G OR LP52G LASER?	Yes

ARE 40 RADIO CHANNELS ENTERED? ONLY ON TD5XO TOUCH DISPLAY.	N/A
ARE ALL OF THE COMPONENTS FIRMWARE UP TO DATE?	N/A
ARE THE UNITS TURNED TO FT AND MPH?	N/A
ARE THE VRS CREDENTIALS ENTERED? TO TEST YOU MUST BE OUTSIDE.	N/A
DOES THE MODEM HAVE INTERNET?	N/A
HAS THE BLADE ROTATION BEEN CALIBRATED WITHIN THE LAST YEAR?	N/A
HAS THE BODY SENSOR BEEN CALIBRATED IN THE LAST YEAR? IF NO, RECALIBRATE.	N/A
HAS THE PASS MATCH ADJUSTMENT BEEN CALIBRATED IN THE LAST YEAR?	N/A
HAS THE VALVE CALIBRATION BEEN CALIBRATED IN THE LAST YEAR?	N/A
IS THE SYSTEM ECM FIRMWARE AT 2.16 OR HIGHER?	N/A
IS THERE A MACHINE FILE SAVED? ONLY ON TD5XO TOUCH DISPLAY.	N/A
IS “SOFTWARE MAINTENANCE UNTIL” DATE OLDER THAN TODAY’S DATE? (IF NO, CONTACT CON TECHNOLOGY SUPPORT)	N/A
MONITOR/ONBOARD DEVICES: ALL GREEN?	N/A
STORAGE: ARE THE PROJECTS DELETED?	N/A
WAS THE SENSOR CORRECTION CHECK PERFORMED ON EARTHWORKS MACHINE? (MUST BE PERFORMED EVERY 1,000 HOURS)	N/A

CHECK BLADE TIPS/CUTTING EDGE ON CONTROL POINT (USE ROVER IF AVAILABLE)NEEDS TO BE WITHIN ONE TENTH OF A FOOT) IS IT ACCURATE?	N/A
CHECK BLADE TIPS/CUTTING LENGTHS ARE CORRECT	N/A
RUN AUTOMATICS BY BENCHING BLADE/BUCKET ABOVE GROUND ON HIGH THROTTLE. MOVE JOYSTICKS WHILE OPERATING TO ENSURE AUTOMATIC CORRECTION. CREATE A POSITIVE 0.5FT OFFSET	N/A